Most paid pre-start checklists give you a flat list of 50 items. The problem is that they treat every fault the same, burying massive safety hazards under minor checks.We know pre-starts can feel rushed, especially when you are on kilometre rates and just want to get on the road safely. To help, we went through …
Most paid pre-start checklists give you a flat list of 50 items. The problem is that they treat every fault the same, burying massive safety hazards under minor checks.
We know pre-starts can feel rushed, especially when you are on kilometre rates and just want to get on the road safely. To help, we went through NHVR guidance, Big Rigs enforcement reports, and driver feedback to build a free truck pre-start checklist for Australia that works a bit differently. We put the brakes, couplings, and tyres first, separated the checks by truck type, and kept the steps clear and practical.
Before you start: Getting paid for your time
Under the Heavy Vehicle National Law, inspecting your truck and filling out the paperwork is classified as “work” for fatigue-regulated heavy vehicles (over 12 tonnes GVM). It counts towards your work hours. In NSW, there is even a special rule about sitting in the driver’s seat with the engine running. Check the NHVR definition of work and work time for the exact details. Note: The HVNL does not apply in Western Australia or the Northern Territory, so WA and NT drivers need to check local rules.
Table of Contents
- The 10-Minute Core Check
- The Full Check
- Vehicle Add-Ons
- Why the Tug Test is Not Enough
- Checking Lights Without a Spotter
- Real Cases: Why Pre-Starts Matter
- If Asked to Drive a Defective Truck
- Free Printable Checklist Download
The 10-Minute Core Check
This is the practical minimum for when you are short on time. These are the main faults that cause major accidents or attract heavy fines.
| Item | What to look for | What to do |
|---|---|---|
| Brakes | Listen for air leaks. Watch the dash gauge for normal pressure build-up. | STOP: Do not drive if leaks are loud or pressure is slow. |
| Couplings | Get under the apron with a torch. Are the fifth wheel jaws fully closed? | STOP: Do not drive if jaws are open or the pin is sitting high. |
| Wheels | Look at wheel nuts, indicators, and check for fresh oil from hub seals. | STOP: Do not drive with loose nuts or heavy oil on wheels. |
| Tyres | Check for flats (especially inner duals) and kick out trapped rocks. | STOP: Do not drive on flat tyres or with rocks jammed in. |
| Lights | Check headlights, indicators, and brake lights actually turn on. | REPORT: Tell the workshop. STOP: Do not drive at night without headlights. |
This is a guide, not legal advice. The final call sits with the driver and a qualified mechanic.
The Full Check
Use this detailed list at the start of your work week or when you pick up a truck from the workshop.
Brakes
| Item | What to look for | What to do |
|---|---|---|
| Air leaks and pressure | Listen for leaks. Watch dashboard gauges for normal pressure build-up. | STOP: Do not drive if pressure drops fast. |
| Slack adjuster & pushrod | Look for excessive travel in the pushrod when brakes are applied. | REPORT: Tell the workshop immediately. |
| Brake chambers | Look for physical damage or loose mounting bolts. | STOP: Do not drive if a chamber is broken or loose. |
| Oil on drums or seals | Check behind the wheel for oil leaking onto brake components. | STOP: Do not drive if oil is coating the brakes. |
| Trailer ABS/EBS | Check the plug is in. Watch the ABS warning light behaviour on the dash. | REPORT: Tell the boss if the warning light stays on. |
| Trailer brake lights | Press the pedal and check they work. | REPORT: Fix blown bulbs before the trip. |
Couplings
| Item | What to look for | What to do |
|---|---|---|
| Fifth wheel jaws | Use a torch under the apron. Jaws must be fully closed. | STOP: Do not drive if jaws are not locked. |
| Locking latch | Check the locking latch or handle is in the locked position. | STOP: Do not drive if the handle is out. |
| Kingpin and bolts | Look for cracks or loose bolts around the turntable base. | STOP: Do not drive with cracked mounts. |
| Pintle or Ringfeder | Check for play. Make sure locknuts are tight on truck and dog setups. | STOP: Do not drive if the pin is worn or loose. |
| Air and electrical lines | Check they are connected tightly and not chafing on the chassis. | REPORT: Tape or tie up chafing lines. STOP: Do not drive with air leaks. |
| Dolly drawbar & chains | Check safety chains are crossed and attached securely. | STOP: Do not drive without attached safety chains. |
Wheels and Tyres
| Item | What to look for | What to do |
|---|---|---|
| Wheel nuts | Look for missing nuts or indicators pointing the wrong way. | STOP: Do not drive until nuts are torqued. |
| Hub seal leaks | Look for fresh oil running down the rims. | REPORT: Tell the workshop. |
| Tyre pressure | Check pressure, including the inner duals. | REPORT: Inflate low tyres. STOP: Do not drive on a flat. |
| Trapped rocks | Look for large rocks jammed between dual wheels. | STOP: Remove rocks before driving. |
| Tread and sidewalls | Check for deep cuts, bald patches, or signs of a separating retread. | STOP: Do not drive with wire showing or peeling retreads. |
Steering and Suspension
| Item | What to look for | What to do |
|---|---|---|
| Steering looseness | Check for excessive wandering or play in the steering wheel. | REPORT: Tell the workshop before the next trip. |
| Pitman arm & linkages | Look for visible movement or loose joints under the front. | STOP: Do not drive with loose steering linkages. |
| Shock absorbers | Look for heavy oil leaking down the side of the shock. | REPORT: Tell the workshop. |
| Torque rod bushes | Check rubber bushes for tearing or missing pieces. | REPORT: Add to the workshop list. |
| Springs and air bags | Look for cracked spring leaves, deflated air bags, or loose cross-member bolts. | STOP: Do not drive on a broken spring or flat air bag. |
Lights and Visibility
| Item | What to look for | What to do |
|---|---|---|
| Headlights & indicators | Check high beam, low beam, and all blinkers work. | REPORT: Fix blown bulbs. |
| Brake & marker lights | Check brake lights and clearance lights work. | REPORT: Fix blown bulbs. |
| Rear marker plates | Check for fading, damage, or peeling reflective tape. | REPORT: Replace plates if they are unreadable. |
| Mirrors, glass, wipers | Look for smashed mirrors, large cracks in view, and torn wiper blades. | REPORT: Replace torn blades. STOP: Do not drive with smashed mirrors. |
Fluids and Engine
| Item | What to look for | What to do |
|---|---|---|
| Engine oil & coolant | Check dipstick and overflow tank levels. | DRIVE: Top up if needed. |
| Power steering fluid | Check reservoir level. | DRIVE: Top up if needed. |
| Fuel and AdBlue | Check gauges and tank caps for leaks. | DRIVE: Fill up before leaving. |
| Belts, hoses, and leaks | Look for frayed belts, bulging hoses, or puddles under the truck. | REPORT: Tell the workshop about minor leaks. STOP: Do not drive if pouring fluids. |
Load and Body
| Item | What to look for | What to do |
|---|---|---|
| Curtains and gates | Check curtains are tensioned and gates are pinned in place. | STOP: Do not drive with loose gates. |
| Latches and doors | Check rear doors are closed and latched properly. | STOP: Do not drive with swinging doors. |
| Load restraint | Check straps, chains, and dogs are tight and in good condition. | STOP: Do not move until the load is legal and tight. |
| Hydraulics, pins, locks | Check tipper or tail lift hydraulics. Check tray pins and locks. | REPORT: Tell the workshop about weeping rams. |
Cab and Paperwork
| Item | What to look for | What to do |
|---|---|---|
| Seat belt and horn | Check the belt locks. Press the horn. | STOP: Do not drive with a broken seat belt. |
| Reverse alarm | Check the beeper or squawker sounds in reverse. | REPORT: Tell the workshop if silent. |
| Safety gear | Check fire extinguisher, first aid kit, and emergency triangles. | REPORT: Restock if missing. |
| Work diary | Check work diary entry for the day has the date filled in. | STOP: Do not drive without dating the page. |
| Pre-start time | Check pre-start time is recorded as work time where it applies. | DRIVE: Note it and carry on. |
Vehicle Add-Ons
You do not need to check everything—just pick the section for what you are driving today.
Rigid Trucks
- Body condition: Check tray or box mountings to the chassis.
- Tipper or tail lift: Look for hydraulic fluid leaks or damaged controls.
- PTO: Check the PTO engages and disengages smoothly. Report it to the workshop if it grinds.
Prime Mover and Trailer
- Fifth wheel: Check the grease level on the plate and the jaw locking mechanism.
- Landing legs: Check they wind up fully and the handle stows away. Low legs will catch on crossings.
- Trailer curtains: Check for major tears and test the buckle tensioners.
- Connections: Make sure air and electrical lines are clear of the catwalk so they do not drag.
Truck and Dog Combinations
- Pintle / Ringfeder: Check the pin is secure, wear is acceptable, and safety locks are engaged.
- Drawbar: Check the drawbar eye for heavy wear and test the bush bolts.
- Dog trailer brakes: Check air lines are connected and trailer brakes actually engage.
- Dog trailer lights: Check the plug connection and test indicators and brake lights.
Why the Tug Test is Not Enough
A tug test is standard practice, but it is not a complete check. The NHVR released safety advice following a spike in trailer drop and decoupling incidents in March 2026.
A tug test can easily pass when the kingpin is sitting on top of the jaws, completely unlocked. You have to physically check the fifth wheel. Use a torch, look under the apron, and make sure the jaws are closed solid around the pin.
Checking Lights Without a Spotter
Drivers often report that it is hard to test brake lights alone in an empty yard. If you have no one to watch the rear:
- Brake lights: Back up to a reflective surface, like a shed wall or another trailer. Look in your mirrors for the red glow when you press the pedal.
- Reverse alarm: Engage reverse with the engine off but the ignition switched on. Walk around the back and listen.
Real Cases: Why Pre-Starts Matter
The Supagas Rollover
In January 2019, a wheel came off a Supagas truck on Melbourne’s EastLink and the truck rolled, spilling about 200 gas cylinders across the highway. WorkSafe Victoria alleged the company should have required wheel checks in pre-starts, used wheel nut indicators, and required a documented wheel check 50 to 100 km after a service. The company was found guilty at trial of failing to provide a safe work environment and was fined $50,000 in February 2025 (sentenced without conviction). Read the report on the $50,000 fine here.
The $580 Logbook Date
Missing a simple paperwork step can be costly. A Queensland driver told Big Rigs he was fined $580 at the Marulan weighbridge in NSW simply for not writing the date in his logbook, after pulling in because a headlight blew. Always date the page before you put the truck in gear. Read the driver’s account here.
If Asked to Drive a Defective Truck
Drivers sometimes feel pressure from dispatch to drive defective trucks to keep the freight moving. The NHVR breaks defects down into three clear types to help you make the right call:
- Major: Imminent and serious safety risk. Do not drive.
- Minor: A safety risk that is not imminent and serious.
- Self-clearing: No safety risk, or an unreadable number plate. Can be used for up to 28 days.
Read the NHVR definitions for heavy vehicle defects.
If you are instructed to drive a truck with a major defect, you can call the Heavy Vehicle Confidential Reporting Line on 1800 931 785, Monday to Friday, 7am to 4:30pm AEST.
Manage Inspections Easily with Fleet Mate
Paper checklists often get covered in grease or lost in the cab. Digital records help fleets keep a clear, organized history of when a truck was checked and who checked it.
Fleet Mate Feature
Manage Inspections Easily with Fleet Mate
Paper checklists often get covered in grease or lost in the cab. Digital records help fleets keep a clear, organized history of when a truck was checked and who checked it.
Check out our fleet inspection management platform to see how we track pre-starts and monitor GPS tracker battery drain on a single screen. Need help setting up hardware? See our complete Teltonika installation guide.
FAQ
Is a pre-start legally required?
The law says you must record work time, and inspecting a fatigue-regulated vehicle is classified as work. Check NHVR guidelines for exactly what information you must record.
Does a pre-start count as work time?
Yes. Under the Heavy Vehicle National Law, inspecting a vehicle over 12 tonnes GVM counts as paid work time.
What is the difference between minor and major defects?
A major defect is an imminent and serious safety risk. A minor defect is a safety risk that is not imminent and serious.
Can I refuse to drive a defective truck?
Yes, you must use your own judgement, especially for major defects. You can report safety issues to the Heavy Vehicle Confidential Reporting Line.
How long should a pre-start take?
A core check of the main safety items (brakes, wheels, couplings) takes around 10 minutes. A full weekly check takes longer.






